Emergency Furnace Repair
No heat in a cold snap: frosted vents, frozen condensate lines, failed igniters and inducer motors, fixed or made safe first.
Southeast Edmonton · T6X
Furnace Repair in Ellerslie
No-heat repairs, tune-ups, furnace replacement, air conditioning, heat pumps and hot water tanks for Ellerslie homes, with the diagnosis explained and the price in writing before work starts.
- Typical drive around 25 minutes
- No-heat calls prioritized
- Price in writing before any work
- ~25 min Typical drive to Ellerslie
- T6X Postal code area
- ~15 yrs Typical home age
- 15–20 Years most furnaces last
Heating in Ellerslie
What Fails in Ellerslie, and Why
Ellerslie covers 2000s to 2010s neighbourhoods south of Mill Woods along Ellerslie Road. Homes are high-efficiency, tightly built and fitted with HRVs.
Working the area
Service calls around Ellerslie Road and Mill Woods, and the streets between.
Notes from Ellerslie service calls
Ellerslie's houses went up through the 2000s and 2010s, and most of the furnaces are in the middle of their lives. That is the age of cheap, common failures. A flame sensor coated with residue makes the burners light and cut out after a few seconds; cleaning or replacing it is typically $129 to $299. A hot surface igniter that finally cracks leaves the inducer running with no flame, and that is $225 to $450. Both are typical Edmonton ranges confirmed in writing before work starts, and both are sensible repairs on a furnace this age. The winter trouble specific to newer homes is condensate.
A high-efficiency furnace produces water, and if its drain line runs past a cold garage wall or through an unheated corner, it freezes and the furnace shuts down on its pressure switch. You can look at the line and trap for ice or a kink; do not cut it. The PVC vents outside should be checked after every heavy snowfall, especially on the side of the house where drifts collect. HRVs in these homes often go years without a clean. Ellerslie homeowners asking about central AC or a heat pump are usually in a good position, since the houses are tight and the ducts are recent.
What We See Most
Common Heating Problems in Ellerslie
The patterns behind most Ellerslie service calls, given the age of the homes and how they were built.
-
Frozen condensate lines where they run to a drain in an unheated space
-
Side-wall PVC vents blocked by snow and frost from the exhaust plume
-
Dirty flame sensors and failing igniters on 10 to 15 year old builder furnaces
-
HRVs frozen or unbalanced after years without service
Something else in Ellerslie?
A furnace that short-cycles, a noisy blower, an HRV that froze, a hot water tank that runs out fast: tell us what it is doing and when it started.
Send a request
Services in Ellerslie
Every Service, Same Written Price
Furnace Maintenance and Tune-Up
A real tune-up before winter: combustion test, flame sensor, igniter, pressure switch, condensate trap, filter and vents.
Furnace Replacement
Swapping a tired furnace for a 95–98% unit, including the chimney and hot water tank venting questions older homes raise.
Furnace Installation
High-efficiency furnaces sized from a heat loss calculation, vented right for snow, with the gas permit and inspection.
Air Conditioner Repair
Capacitors, contactors, refrigerant leaks and frozen coils on the few hot weeks a year you actually need the AC.
Water Heater Repair and Replacement
Hot water tank repair and replacement: gas, power-vent and tankless, with sediment, venting and the gas permit handled.
Before We Arrive
Four Things Worth Doing First
Some no-heat calls end at step one. The rest go faster when we know what the furnace did before it stopped.
Step 1: Check the Basics
Thermostat set to heat and above room temperature, batteries, the furnace switch and breaker, and a filter that isn't grey and bowed.
Step 2: Look at the Vents
From outside, find the two white PVC pipes. Snow drifted over them or a ring of frost inside is the most common cold-snap shutdown.
Step 3: Read the Blink Code
Count the flashes on the board through the sight glass on the blower door. The chart is inside the door. It saves diagnostic time.
Step 4: Send the Request
Community, furnace age if you know it, what it's doing and the blink code. We reply with an arrival window for Ellerslie.
Furnace Repair in Ellerslie
Tell us what the furnace is doing. We reply with an arrival window and a price range, and the price is confirmed in writing before any work starts.
Nearby Communities
Also Covering Southeast Edmonton
1950s bungalows by Mill Creek, the Mill Woods suburbs and new neighbourhoods to the south.
All Service AreasPermits & Safety
What to know before any gas work in Ellerslie
- Permits in Ellerslie A furnace or hot water tank replacement needs a gas permit through the City of Edmonton, followed by an inspection. The contractor pulls it.
- Door-to-door offers Alberta banned door-to-door sales of furnaces, air conditioners and hot water tanks on 1 March 2019. Anyone knocking with a furnace deal is already breaking the rule.
- Gas smell or CO alarm Get out first, don't touch switches or the thermostat, and call ATCO Gas's 24-hour emergency line or 911 from outside. Book the repair after.
Ellerslie Questions
What Ellerslie Homeowners Ask
Straight answers on timing, local failure patterns, cost and permits.
All QuestionsHow quickly can you get to a no-heat call in Ellerslie?
No-heat calls get priority, and typical drive time to Ellerslie is around 25 minutes from wherever the technician is working. We confirm the arrival window when we reply to your request rather than promise a time we can't keep. While you wait, check the thermostat, the furnace switch and breaker, the filter, and the two PVC vent pipes outside for snow or frost.
What furnace and HVAC problems are most common in Ellerslie?
The pattern we see most in Ellerslie is frozen condensate lines where they run to a drain in an unheated space, followed by side-wall PVC vents blocked by snow and frost from the exhaust plume. Ellerslie covers 2000s to 2010s neighbourhoods south of Mill Woods along Ellerslie Road. Homes are high-efficiency, tightly built and fitted with HRVs. Cold snaps stress every furnace in the region, so frosted vents, frozen condensate lines and worn igniters show up in every community.
What does furnace repair cost in Ellerslie?
Typical Edmonton ranges apply in Ellerslie: a diagnostic visit runs $129 to $199 in regular hours and $199 to $349 after hours. Common parts include an igniter at $225 to $450, a flame sensor at $129 to $299 and an inducer motor at $650 to $1,400. A new high-efficiency furnace, installed, typically runs $4,800 to $7,500 for a single-stage unit. Your price is confirmed in writing before any work starts.
Does a furnace replacement in Ellerslie need a permit?
Yes. Replacing a gas furnace or a gas hot water tank needs a gas permit through the City of Edmonton, and an inspection after the work. The contractor pulls the permit; gas work in Alberta is done by a certified gasfitter. Ask to see the permit number on your quote or invoice.
No Heat in Ellerslie? Tell Us What It's Doing.
No-heat calls get priority. We reply with the arrival window for Ellerslie and a price range, and nothing is done without your OK in writing.
